Emergency Generator Exhaust System Design | USP&E

Emergency Diesel Generators

Emergency Diesel Generator Exhaust System Design: Back Pressure, Routing and Safe Discharge

An emergency diesel generator can be perfectly sized and still fail its first long run because of the exhaust. Too much back pressure robs power and raises temperatures, a badly supported pipe cracks a turbocharger housing, and a poorly placed outlet sends fumes straight into the building’s air intakes. These problems are designed in, and they are expensive to fix once the pipe is installed.

This guide explains how an emergency generator exhaust system is designed, from the engine outlet to the point of discharge. It is written for building services engineers, facility managers and contractors installing standby sets in plant rooms, on roofs or in enclosures at hospitals, offices, data rooms and industrial sites.

Back pressure: the number that drives the design

Every engine datasheet gives a maximum allowable exhaust back pressure at rated load, measured close to the turbocharger outlet. It is usually a few kilopascals, or a few tens of inches of water. Above it, the engine cannot expel exhaust freely, cylinder temperatures rise, fuel use increases and output falls. Emissions certification is also tied to operating within that limit.

The designer’s task is to keep the total pressure drop of the whole system, including pipe, bends, silencer, any aftertreatment and the outlet fitting, below the limit with some margin. That calculation should be done before pipe sizes are fixed and repeated if the route changes during construction.

Sizing pipe and counting the bends

Pressure drop depends mainly on exhaust gas flow, temperature, pipe diameter and the equivalent length of the run. Each elbow adds the equivalent of a length of straight pipe, and short-radius bends add much more than long-radius ones. A run that looks short on the drawing can become long once several bends and a rise to roof level are counted.

Manufacturers publish exhaust flow and temperature at rated load, and silencer makers publish pressure drop curves. With those figures, the designer works out the drop for each section and adds them. If the total is too high, the usual fixes are a larger pipe diameter, fewer or gentler bends, or a silencer with lower resistance. Upsizing the pipe for the whole run is often the simplest answer.

Remember that exhaust gas density falls as temperature rises, so the calculation must use the flow and temperature at rated load rather than at idle. Where several generators discharge into a common stack, which is generally discouraged, each set must be protected from backflow from the others and the combined pressure drop checked for every running combination.

Silencers, connectors and supports

Silencers are offered in grades often called industrial, residential and critical or hospital grade, with increasing attenuation and usually increasing pressure drop. The grade follows the site’s noise limits, which our page on acoustic and emissions packaging discusses in more detail.

A flexible connector at the engine outlet absorbs engine vibration and thermal growth. It must not be used to take up misalignment or to carry weight. The pipe and silencer are supported independently from the building structure, with fixed points and guides placed so thermal expansion is directed where it can be absorbed. The aim is that no static load from the exhaust system rests on the turbocharger.

Heat, insulation and penetrations

Exhaust surfaces run hot enough to cause burns and ignite nearby materials. Inside plant rooms the pipe is normally insulated or lagged, which also reduces the heat load that room ventilation has to remove, as described in our note on plant room ventilation. Clearances to combustibles follow the applicable codes, such as NFPA 37 in the US, and local building rules.

Where the pipe passes through walls or roofs, a ventilated thimble or sleeve keeps the building structure cool and preserves the fire rating. Weatherproof flashing, a rain cap or flapper and a condensate drain at the low point keep water out of the engine. Water entering the exhaust while the set is idle is a known cause of internal corrosion and hydraulic damage at the next start.

Where the exhaust goes

The discharge point should send exhaust up and away from people, windows, doors and any air intake, including the generator’s own radiator and combustion air inlets. Prevailing wind, nearby taller buildings and roof equipment all affect whether fumes come back. Re-entrainment of exhaust into a hospital or office ventilation system is a serious health risk and a common complaint.

Stack height and position are often checked against building services guidance and, for larger sets, against the conditions of the air permit. Where diesel particulate filters or SCR units are fitted, their pressure drop, weight, access for cleaning and temperature needs become part of the exhaust design. Light-load running habits matter too, and are covered in our page on wet stacking control.

Inspection and testing

At commissioning, back pressure should be measured at rated load and compared with the design value and the engine limit. Supports, flexible connectors, drains and rain caps are checked, and the exhaust route is inspected while the set runs to confirm there are no leaks into occupied spaces.

In service, the exhaust system belongs in the routine inspection list: lagging condition, connector cracks, support integrity, drain operation and soot staining near joints. A rise in measured back pressure over time can point to a blocked silencer or a filter needing service. Treating the exhaust as part of the engineered installation rather than an afterthought keeps an emergency set ready for the long run it may one day need.

Keep the design records with the set: the back pressure calculation, silencer data, support drawings and commissioning readings. When a set is later moved, upgraded with aftertreatment or given a longer route, those records let the new design start from verified numbers instead of guesses.

About the authors

This guide comes from the USP&E installation designers who route exhaust, ventilation and fuel for standby sets. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. Ongoing care of installed sets is covered by our operations and maintenance services.

Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.

Exhaust system questions

What is exhaust back pressure on a diesel generator?

The resistance the exhaust system puts on gas leaving the engine, measured near the turbocharger outlet and limited by the engine datasheet.

What happens if back pressure is too high?

The engine loses power, runs hotter, uses more fuel and may exceed its emissions certification limits.

How do you reduce exhaust back pressure?

Use a larger pipe, fewer or long-radius bends, a lower-resistance silencer or a shorter route to the discharge point.

Why is a flexible connector needed?

It isolates engine vibration and absorbs thermal growth. It should never carry pipe weight or correct misalignment.

Where should a generator exhaust discharge?

Upward and away from people, windows, doors and all air intakes, including the generator’s own radiator and combustion air.

Should the exhaust pipe be insulated?

Inside buildings, usually yes, to protect people and materials and to reduce the heat that room ventilation must remove.

Get your exhaust design checked

Send the engine datasheet, plant room layout and proposed exhaust route, and our engineers will check back pressure, supports and discharge position before installation starts.

Phone +27 10 822 2324 during office hours, or write to info@uspeglobal.com at any time; the installation design enquiry also routes straight to our project engineers. Emergency and standby sets can be browsed in our diesel generator stock.


Where we operate

USA | AFRICA | UK | UAE | CHINA

USP&E United States

Colorado Springs Office: 1755 Telstar Dr, Suite 300

Knoxville Office: 800 S Gay St, Suite 700

USP&E South Africa

Johannesburg Office: 22 Kildoon Rd, Bryanston

Cape Town Office: 31 Brickfield Road, Woodstock

USP&E United Kingdom

London Office: 162-168 Regent Street

USP&E China

China Office: No. 1, Ningzhou Road, Wuxi

Call:+27 10 822 2324  |  E:info@uspeglobal.com

ISO Certifications
ISO9001ISO45001

Powering Possibility. Built for the Frontier.
Full-service EPC & O&M. Not a broker.

© 2026 USP&E · Emergency Diesel Generators is part of USP&E