This article explains what wet stacking is, why it happens, how to recognise it and, most usefully, how to prevent it with sensible loading, test practice and sizing. It is written for facilities managers, maintenance supervisors and anyone responsible for an emergency generator that has to start and carry load on demand.
What wet stacking means
A diesel engine burns fuel efficiently when its cylinders are hot and the load is high enough to keep combustion temperature up. At light load, the cylinders run cooler, the fuel does not burn completely and some of it leaves the cylinder as unburned fuel, soot and oily vapour. The exhaust then carries a wet or sooty mixture into the manifold, turbocharger and stack. The name comes from the wet appearance at the exhaust outlet.
The problem is mechanical and chemical. Unburned fuel can wash oil from cylinder walls, dilute the lubricating oil and leave carbon deposits on piston rings, valves, injectors and turbocharger parts. Over time, compression drops, smoke increases and the engine becomes harder to start or less able to carry its rated load. A standby engine that cannot carry full load in an emergency has failed the one job it was installed for.
Why standby sets are at risk
Two habits drive wet stacking. The first is testing at no load or very light load for long periods. The second is installing a generator that is much larger than the real load. If a 500 kW set carries a 100 kW building, it operates at 20 percent load whenever it runs, which is below the level many manufacturers recommend for sustained operation.
Manufacturers often suggest keeping a diesel engine at roughly 30 to 50 percent of its rating or more during extended runs, but the exact guidance differs by engine and should come from the operation manual. Generators also idle and warm up without load during starts. Good practice keeps these periods short and does not leave a set running unloaded to prove it still starts. The sizing steps in our guide to generator sizing in kW, kVA and amps help avoid sets that are far larger than the load.
Signs to look for
Wet stacking leaves evidence that a routine walk-round can pick up. None of these signs proves the diagnosis alone, but several together call for action.
- Black smoke or an oily, wet sheen at the exhaust outlet, sometimes with dark liquid dripping from the stack or silencer drain.
- Carbon deposits and fuel residue on the turbocharger outlet, exhaust manifold or flexible joints.
- Rising crankcase oil level with a thin, fuel-like smell, which can point to fuel dilution.
- Lower than expected output or poor load acceptance during a test.
- Higher blow-by, difficult starting or excess smoke on a first load step.
Oil analysis is a useful check. Laboratories can measure fuel dilution, viscosity and wear metals. A trend of rising fuel in oil on a lightly used engine often tells more than a visual inspection.
How load bank testing helps
A load bank puts a resistive load on the generator so that the engine can be run at a proper loading for a defined time. This burns off deposits and proves that the set can carry its rating. Many sites combine monthly exercises with an annual load bank test, and add a load bank run after long periods of light running.
Where the building load cannot give enough load, a portable or permanently installed load bank allows the correct duty to be applied. The load bank should be sized to bring the engine up to the loading recommended by the manufacturer, with enough duration for temperatures to stabilise. Test records should show kW, kVA, voltage, frequency, coolant and oil temperature and any alarms, as described in our post on emergency generator test records and compliance.
Warm-up, cooldown and starting practice
Extended idling is rarely helpful. After starting, a standby set should come up to speed and take load as soon as the control system permits, because load heats the cylinders faster than idling does. Equally, before stopping after a loaded run, a short cooldown at low load allows the turbocharger and bearings to settle, but it should not be stretched into a long idle.
For emergency generators, block heaters and pre-lubrication systems keep the engine ready to accept load quickly. Procedures should be consistent so that every operator treats the generator the same way, and should be stated on a laminated card at the control panel for those carrying out tests.
Corrective steps and good design
If a generator is already showing signs of wet stacking, the first remedy is usually a managed period under high load, within the manufacturer’s limits, to burn off deposits. Severe cases may need injector service, turbocharger cleaning, a check of piston rings and cylinders and an oil and filter change. A maintenance technician should decide on the extent of work after inspection.
Prevention starts at design. Match the generator to the real load profile, include provisions for a load bank connection and write a testing plan that includes loaded runs. For fleets that have grown beyond their original duty, the broader approach is set out in our notes on emergency generator fleets and fuel resupply, which covers fuel and capacity planning alongside testing.
About the authors
This guide comes from the USP&E diesel service engineers who inspect, test and load bank standby generators. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. Our maintenance scope is outlined on our operations and maintenance page.
Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.
Wet stacking questions
What is wet stacking in a diesel generator?
It is the build-up of unburned fuel, soot and oily residue in the engine and exhaust, caused by running at low load so that combustion stays too cool.
What load avoids wet stacking?
Manufacturers often advise roughly 30 to 50 percent of rating or more during extended runs, but the exact figure comes from the engine’s operation manual.
Is wet stacking harmful to the generator?
Yes. It can foul injectors, glaze cylinders, dilute the lubricating oil and reduce the engine’s ability to carry full load.
How can I tell if my generator has wet stacking?
Look for oily or black residue at the exhaust outlet, carbon at the turbocharger, fuel in the oil, poor load acceptance and heavy smoke.
Does load bank testing fix it?
A load bank run at proper loading can burn off deposits and proves the set can carry its rating, though severe cases may also need injector or turbocharger service.
Can an oversized generator cause the problem?
Yes. If a set is much larger than the real load, it runs at low percentage load every time and is prone to wet stacking.
Have a generator inspected
Send your generator model, load profile and recent test records, and our diesel engineers will advise on load testing, sizing and any corrective work needed to keep the set ready.
Phone +27 10 822 2324 during office hours, or write to info@uspeglobal.com at any time; the generator inspection enquiry also routes straight to our project engineers. Standby diesel sets are listed in our diesel generator inventory.
